A scruffy garden gate can make your house look bad and appear unwelcoming to guests and passers-by. However, fixing your garden gate is not hard, and can be done in 13 simple steps. Express.co.uk has everything you need to know about building a wooden garden gate.
How to make a garden gate
According to WikiHow.com, this is how a wooden garden gate is built.
Step one: Get tools and materials ready. You’ll need:
- Power drill
- Compound miter saw
- Carpenter’s level
- Jigsaw, for cutting a decorative profile
- 3-inch stainless steel coated deck screws, for putting the box frame together
- 1 ¼ or 1 ⅝ stainless steel or coated deck screws, for planking
- How to lay garden sleepers
Step two: Make sure fence posts can support a gate.
The size of the garden gate should not exceed four feet (1.22m). Measure the entry at the top and bottom as they can easily be different.
Step three: Anchor and plumb the fence posts, if necessary.
WikiHow’s Anthony TC Williams said: “You need to make sure that hanging the gate won’t pull the posts to one side. The way you anchor the post will depend on the size of the fence, but in general, you need to make sure the post doesn’t wiggle with weight.
“If it can be easily moved, the gate will sag. You should also check and see that the post is level, straight up and down.”
Ideally, a four-foot (1.22 m) tall gate needs a five inches x five inches (12.7cm x 12.7 cm) redwood post.
The hole that the post will occupy should be at least 6 inches deeper than post will be buried. Post should be buried at least 1/3 but preferably 1/2 of its length and hole should be 3 x as wide as post.
Step four: Measure the frame.
The frame for a basic wooden fence gate should be a simple box with four sides, usually somewhat smaller than the gate opening.
If you’ve got a 3×5 opening in the fence, build a 3×4 box out of a weather resistant wood.
Step five: Building the gate.
Cut 2×4 inches (5.08 x 10.16cm) frame pieces to size with a mitre saw.
Start the gate by cutting the top and bottom pieces to the same width/length as you planned for, slightly smaller than the opening in the fence.
What are Aldi’s best buys this week? 5 items to spruce up your garden [TIPS]
How to keep cats out of garden [EXPLAINER]
Garden centres open: When will garden centres reopen? [INSIGHT]
- How to grow herbs indoors
Step six: Screw in the top and bottom planks.
Drill a pilot hole for the screws before putting them in so that they do not split the wood. Fasten with deck screws, pre-drilling to keep the wood from splitting. Measure from the top bend to the opposite bottom corner. Both sides should measure the same.
Step seven: Cut an angled cross-brace and attach it to the top and bottom rails.
Make your diagonal cut with a mitre saw. Place the diagonal onto the box and trance with a pencil where the angles go.
Place the cross-brace at a 45 degree angle extending from the bottom corner of the gate to the opposite corner of the top of the gate.
Step eight: Cut and install the planks.
Cut planks using a table saw and secure them using deck screws, drilling pilot holes to keep your planks nice and clean.
Step nine: Design the top of the gate.
To start, draw an arc across the top of the fence using a string and a pencil, filling it with decorative curves according to your taste. If you’re a woodworker, feel free to get fancy with it. Use the jig to cut along your pattern.
Step 10: Install hinges and attach the gate to the fence.
Put the gate into place, supporting it on the bottom with a 2×4 (1.5 inches off ground). Predrill where the screws will go.
Prop up the gate and screw the hinges into the gate and attach the hinges to the post.
Step 11: Install a gravity latch.
Most easy-to-use fences will use a gravity latch, which you can install after you’ve hung the fence.
Step 12: Seal the wood.
Try to hit every exposed surface with your sealer, using a paintbrush or garden sprayer to apply.
Step 13: Finished! Use your gate.
Source: Read Full Article